EX 34063 PDF

This is a simple-minded design tool that allows you to calculate component values MCA simple switcher chip. It displays the appropriate scematic diagram. Excellent Semiconductor EX datasheet, Monolithic control circuit (1-page), EX datasheet, EX pdf, EX datasheet pdf, EX pinouts. Expdf – Free download as PDF File .pdf), Text File .txt) or read online for free. Expdf.

Author: Dorisar Daigor
Country: Papua New Guinea
Language: English (Spanish)
Genre: Relationship
Published (Last): 1 July 2010
Pages: 241
PDF File Size: 1.60 Mb
ePub File Size: 7.4 Mb
ISBN: 872-4-65567-750-5
Downloads: 71100
Price: Free* [*Free Regsitration Required]
Uploader: Vudogul

Ignore any error messages about unrecognized parameters in the diode model. For designing dc-dc converters, the datasheets have a table of formulas that may be used, however this should not be a replacement for understanding of the circuit operation as the designs may need to be tweaked for a variety of reasons. The aim of these notes is to provide some insight into the operation of the chip and associated circuits.

Dumb switch 2. Switching Mode Power Supply Design. Thru-beam type CX EX 2 m 6. Previous 1 2 It is useful in applications such as providing analogue positive and negative supplies from a single 5V logic supply in small circuit boards. The charge current is modified by a voltage at the Ipk-sense pin to shorten the charge time and so reduce the maximum duty cycle.

A well documented subcircuit file is given here.

The changes in oscillator slope and in the cycle period are clearly visible as the feedback gating signal turns on and off. The following diagram of the model is presented in terms of comparators and standard digital gates for clarity.

Examination of the red oscillator trace shows that the charge time is shorter during a gated on period. Retroreflective type mm Diffuse reflective type Setting distance: The oscillator-source block generates the timing capacitor current in response to the output of the comparator. It includes 3403 number of simple logic gates built from nonlinear dependent voltage sources. We consider the conversion from a 12V input to a 5V output for driving logic circuitry.


Even thoughEX series provides a high-power, narrow beam that can produce a spot as small as 1mm in diameter. Some of the difference may be in the filter capacitor ESR and inductor series resistance which we have assumed as zero. This is needed to prevent the set and reset inputs of the flip flop being active at the same time, and so causing the simulator to choke. Ceramic capacitors in parallel with the power input electrolytic capacitor should be used to attenuate high frequency switching noise.

EX series products are listed by Underwriters’ Laboratories and CSA for use inproduct, the products will have no heating problems.

EX34063 Datasheet PDF

The above circuit can be run as a simulation. The model is different to the AEi model but makes use of some information about MC behaviour. The upward slope of the switch current is due to the ramping up of the inductor current.

As well 340633 the spreadsheet provided here, more comprehensive resources can be found on the web, see in particular references 4 and 5.

MCA design tool

The yellow plot is the feedback comparator gating signal that turns the switching process on and off. Two opensource simulators are provided with the gEDA design suite: In the top right of the circuit is the flip flop that drives the switching transistor. Lazar’s Power Electronics Corner. These chips can be sensitive to noise on the power input rails, resulting in the flip flop triggering prematurely and resulting in poor regulation and overvoltage.


The transistors need to have some capacitances and resistances to be specified to avoid convergence problems. The control functions provided consist simply 3403 a comparator that gives hysteretic or bang-bang control. 3403 reason for this is that at least one capacitor inside the MC model has initial conditions.

It is also valuable for gaining an intuition into how circuits work. This file is not suitable in itself for generating a subcircuit as the gates need to have their supplies referenced to the common pin of the MC rather 334063 to ground this could be done by defining custom symbols. While it is no replacement for 3403 on hardware, it can provide quite good behavioural modelling of complex circuits, allowing many errors and problems to be corrected before the hardware is built.

Practical circuits and problems experienced. Try Findchips PRO for ex The enclosed replaceable basic switch is accessible when the cover is removed. The focus of this page is to study the behaviour of some switching power circuits using the MC Right-click on the graphs and drag a small box to zoom in on the detail. This consists of a comparator working with hysteresis to provide the 1.

Smallest body, ed 3. EXsubjected to liquid splash. The signal “oscillator” provides a pulse that goes low when the capacitor is being discharged. The INA- also features high reverse isolation, making it an excellent candidate for LO buffer applications.